Hole to Install a Gas Fire Buying and Installation Guide

Hole to Install a Gas Fire Buying and Installation Guide

Hello friends, in this article, we have provided details about the Installation of the gas fire in the house, so everyone is requested to read this post down to the full and know all the information about this subject. Enjoy the comfort and atmosphere of a terrible fire in the cold night. Here we will show you how to install a gas fireplace. Do not worry about setting the fireplace. You just throw the chimney out of the house. Once the fireplace is installed, you will just flip a switch to start a shocking fire. Mention below complete details about this topic like installing a gas fireplace on an interior wall, Cost, Benefits or more.

What is Gas Fire?

The gas fire is an open fireplace, which can be installed in the fire basket. All of you know about today’s modern culture that the fire of gas looks very good in any room, as well as a balanced grip, powerful or flames for homes without fire.

How to Install Gas Fireplace in existing chimneys

  1. First gathering stuff for gas fireplace

Tools Required

Here mention below required tools such as

  • Brad Nail Gun
  • Caulk Gun
  • Circular Saw
  • Cordless Drill
  • Drill bit set
  • Drywall Sander
  • Drywall Saw
  • Dust Mask
  • Hammer
  • Hearing Protection
  • Knee Pads
  • Knockdown Knife
  • Level
  • Mud Pan
  • Paintbrush
  • Rasp
  • Roller Sleeve
  • Roller Tray
  • Sanding Block
  • Sanding Pole
  • Screw Gun
  • Socket/Ratchet Set
  • Straightedge
  • Stud Finder
  • T-Square
  • Tape Measure
  • Tin Snips
  • Utility Knife

Material Required

  • 1/2*48*96 drywall
  • 100-grit sandpaper
  • 2*10*12’ lumber (2)
  • 3/4 * 4 * 4 plywood
  • 9’ Vent pipe
  • Acrylic caulk
  • Corner beads
  • Gas Fireplace
  • Heat Shield Flashing
  • Interior Fire stop
  • Joint Compound
  • Metal drip cap
  • Metal Nail Plates
  • Paint or Textured Finished
  • Polyurethane Caulk
  • Silicone Caulk
  • Straight Pipe

Hole to Install a Gas Fire Buying and Installation Guide

Pick a Location for the fireplace

First of all, place for the fireplace in your house and think of keeping it the same where the installation of a gas line, an electric circuit, and an exit pipe is most convenient.

Order a gas fireplace

Ordering your exhaust piping can be the easiest when ordering your fireplace. It will include pipes between fireplace and wall, a wall-pass-through and external piece for pipes.

Build Platform for the Fireplace

The actual chimney unit is quite small and it is dangerous to sit directly on the floor. To get the fireplace from the floor, you will need to create a platform. Use materials that match room decoration, but it will create a non-combustible surface to sit on the chimney. This may include masonry or ceramic tiles for example.

  1. Make an area for gas fireplace

Keep the fireplace in its last position

If you find room in the room where you want to keep the fireplace and keep the stage, then set the fireplace on the platform.

Install exhaust piping at the top, or back, or on the stove

Attach as much as possible to the section going through the wall. This will allow you to find out where the whole should go exactly through your wall.

Cut the hole for the direct venting system

This hole should be the size of the wall-pass-through that was ordered with your stove. Pass-through is designed to keep all heat from combustible wall material, which is a very important part of minimizing the damage caused by fire.

Frame the inner edges of the opening with lumber

The framing you put will form a basis on which pass-through can be attached.

  1. Installing Your Gas Fireplace

Insert a wall-pass-through

Inside the house, place high-temperature clutch on the surfaces inside the hole you made. Push the wall-pass-through into the hole, press it into the coke and make a seal around the pass-through. Then screw it in place.

Complete the direct ventilation system

 Install all remaining piping inside and outside the house.

Now hire licensed contractors to install and connect gas lines and lights

Depending on where you have placed your fireplace, you may need to run new electrical outlets and you will definitely need to run a new gas line. Unless you are qualified to handle these steps yourself, appoint a licensed contractor to complete them.

Make an alternate frame around your fireplace

Many gas fireplaces do not need a mantle or frame around them, some willpower A decorated the wooden frame, in which surrounds, mantle, stove, and any wooden decoration you want.

How much does it cost to install a gas fireplace?

Installation and finishing usually add 173472.57/-. Hiring a professional to establish a connection with a gas line or Propane tank adds about 69389.03/-.

How much does it cost to run a gas fireplace per hour?

The gas chimney running or insertion is really cheap. For example, the heat and gloss 6000, which is one of the most popular gas chimneys ever so far, costs only 42 cents per hour to operate., So it is spending as little as 138.78/- to enjoy the fire for a whole evening.

What are the advantages of holes in a wall gas fire?

The hole in the wall style fireplace may be something new for most, but it is a model of fireplace that is becoming increasingly normal. They come with many plus points that make them more awkward when deciding on your next fireplace.

  • Looks
  • Modern
  • Efficiency